How do you properly break in a generator
Generators

How Do You Properly Break in a Generator (Easy 8 Steps)

As an Amazon Associate, I earn from qualifying purchases. For more information, Check our Affiliate Disclaimer page.

Breaking in your generator is almost an unknown concept for many new users. One of the few practices that, if done in the first few hours of bringing in your generator at home, can increase its lifespan. But how do you properly break in a generator? Yep, this is something that we’re going to explain to you in an understanding manner that you can perform it yourself. 

How Do You Properly Break In a Generator

We’ll now go through a detailed step by step guide in the following sessions. 

What is Breaking In A Generator?

It is not as weird as the name suggests. In fact, the process is a lot easier than most of you think. When you know this simple mechanism can improve your generators’ toughness, you won’t be procrastinating. 

Well, breaking in a generator, in general, refers to a cycle of letting your generator run and changing its oil a couple of times. 

We run it so that the oil goes and travels through the parts, making them more active. Further, new home generator machines, while running, tiny pieces of metal can break and cause serious engine malfunctions. But while running with oil, the engine gives a smoother performance, decreasing the possibilities of any parts breaking inside the engine. 

Let’s see how it is done in a more detailed manner! 

Why Break In A Generator?

Portable generators aren’t like regular items that you buy one every week. You value the hard-earned money that you spent on buying appliances that make your life easier. 

So, anything and everything that can sustain the durability of your portable generator is a plus. This is where the break-in part comes in. 

As breaking in a generator within the first couple of hours is a significant contributor in terms of increasing its longevity, you have no alternatives but to perform it. 

A Step by Step Guide on How to Break in a Generator 

Now you may find yourself in a state of anxiousness as you have little or no knowledge about generator engines. But we got you covered and now walk you through the entire process. 

1. Buy the Required Items 

A few things you need to go shopping before you start the process. When you have all the tools within your reach, even the most complex task gets easy. 

Gasoline – The first item that you should get from the market is Gasoline. You should find the best quality Gasoline from the market. Also, make sure you’re getting the highest-octane Gasoline for the best performance. 

Oil – The second item you’ll be needing is the best quality oil. Here is one thing to consider, instead of trying to find oil of your own choice, it is better to buy the oil your manufacturer has recommended. 

Oil Conditioner – Third, get a premium quality oil conditioner. It will help reduce dry starts, which are detrimental to your heavy-duty generator engine. 

Funnel – To pour the essential liquids properly you’ll also need a funnel.

All the items mentioned here are equipped with special properties that can lubricate your generator engine and make it smoother than ever before. 

2. Start Lubricating 

We can now begin our lubricating as we have all the required materials with us. First, start with removing the spark plug in your generator. Now, use the funnel to pour oil conditioner in the spark plug chamber. 

It will create the primary lubrication before you pull the cord to get your generator started. 

Remember, this is a must! Never try starting your generator by pulling the cord without performing the above-mentioned lubrication process. 

Now while the conditioner oil is poured in, try yanking the cord in slow motion. It will let the piston go up and down inside the well-lubricated cylinder. Now, place the spark plug back again. 

Also, don’t forget to read about Best Extension Cord for Generator

3. Pour Oil 

Now you’d use the oil. Before starting, apply some oil conditioner on the crankcase. Now, again get a funnel and pour in the oil. If you’re confused about how much fuel is needed, you can check your manual. The manufacturer guideline should outline the amount of oil required during breaking in. 

4. Use the Gasoline 

Just usually fill up your generator with a quality Gasoline. 

Open your vent and position it. Start the generator after turning on the choke. 

If the first pull doesn’t start your engine, don’t panic. You need a couple of tries before finally getting it on.

5. Run for One Hour 

Now continue running your generator for one hour slowly. Remember, run the generator with no load in the first hour. 

6. Drain Oil 

When you’re done running it for one hour straight, you’ll have to drain the oil. By draining the oil, you’ll be able to filter out all the metal fragments and flakes from the engine and let it run smoothly. 

When these metal bits and pieces are out of the system, it will save your engine from wear and tear. Now, pour some oil conditioner, followed by new oil. 

7. Run One More Hour 

Then once again, run for another hour and follow the previously stated procedures. Each time put some oil conditioner before pouring oil. Each time you drain, you’d notice the oil is becoming more apparent with each step. 

8. Run it the Last Time 

After draining oil the 2nd time. Follow the previously mentioned process one last time and run it the third time. During the final run, you can add like 500-600 watt load. 

You have, by now, successfully broken in your generator and should be able to use it without any technical issues from now on. 

Well, that’s it. Implement these easy steps after you set up your generator. It will increase the lifespan of your device as well as boost performance for a better output. 

To Sum Up

Generators like all the other devices require thorough maintenance. And breaking in is one of the key maintenance drills that have to be performed each time you get a new generator in. 

This simple procedure will filter out any metal bits or pieces present inside the engine. Reducing the wear, it will contribute highly in terms of providing stable performance. 

And now you know no more questions like how to break in a generator, you can conduct the whole process within several hours. So, the wait is over. Break-in your generator for a smooth and continuous power output!

As an Amazon Associate, I earn from qualifying purchases. For more information, Check our Affiliate Disclaimer page.

Leave a Reply

Your email address will not be published. Required fields are marked *

Social media & sharing icons powered by UltimatelySocial
RSS
Follow by Email
Pinterest
Instagram